Product ID:LIGHTWEIGHT BODY FILLER, DX4
MSDS Date:07/27/1990
FSC:8010
NIIN:00N027627
MSDS Number: BNMBV

PPG INDUSTRIES INC (WAS PTTTSBURGH PLATE GLASS CO)

ONE PPG PLACE
PITTSBURGH, PA 15272-0001
US

Emergency Phone: 412-434-3131

Info Phone: 412-434-3131

Cage: 47695

PPG INDUSTRIES INC

PITTSBURGH, PA 15272 US

Telephone: 1-800-245-2974 (CAL HYPO)

Cage: 47695

TALC (POWDER), CONTAINING NO ASBESTOS FIBERS; (MAGNESIUM

CAS: 14807-96-6

RTECS: WW2710000

Fraction By Weight: 30-35%

OSHA PEL 2 MG/M3 RESP

ACGIH TLV: 2 MG/M3 RESP

STYRENE (SARA III)

CAS: 100-42-5

RTECS: WL3675000

Fraction By Weight: 15-20%

OSHA PEL 100 PPM

ACGIH TLV: S,50PPM/100STEL;9293

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

FILM FORMERS, RESINS AND ADDITIVES

Fraction By Weight: 50-55%

OSHA PEL NOT APPLICABLE.

ACGIH TLV: NOT APPLICABLE.

THE PRESENCE OF UV LIGHT MAY ENHANCE

RTECS: 9999999ZZ

OSHA PEL NOT APPLICABLE.

ACGIH TLV: NOT APPLICABLE.

DURING/FOLLOWING USE OF THIS PROD, CONT A POIS CTL

RTECS: 9999999ZZ

OSHA PEL NOT APPLICABLE.

ACGIH TLV: NOT APPLICABLE.

*INGESTION *EXCESSIVE EXPOSURE TO A CORROSIVE

RTECS: 9999999ZZ

OSHA PEL NOT APPLICABLE.

ACGIH TLV: NOT APPLICABLE.

AIRBORNE CONTAMINANTS AGAINST WHICH THE

RTECS: 9999999ZZ

OSHA PEL NOT APPLICABLE.

ACGIH TLV: NOT APPLICABLE.

LOWEST SUGGESTED EXPOS LIMITS, THE LEL BELOW STATED

RTECS: 9999999ZZ

OSHA PEL NOT APPLICABLE.

ACGIH TLV: NOT APPLICABLE.

CUTTING ON SURFACES COATED W/THIS PRODUCT.

RTECS: 9999999ZZ

OSHA PEL NOT APPLICABLE.

ACGIH TLV: NOT APPLICABLE.

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:YES OSHA:NO
Health Hazards Acute and Chronic:ACUTE: INGEST:HARMFUL IF SWALLOWED.
EYE:CAUSES IRRIT. SKIN:MAY CAUSE MOD IRRIT. INHAL:VAP/SPRAY MIST
MAY BE HARMFUL. IRRITATES EYES, NOSE & THROAT. RPTD EXPOS TO HIGH
VAP CONC MAY CAUSE IRRIT OF RESP SYS & PERM BRAIN & NERV SYS DAM.
INTENTIONAL MISUSE BY DELIBERATELY CONCENTRATING & (EFTS OF
OVEREXP)
Explanation of Carcinogenicity:STYRENE: GROUP 2B (IARC)
Effects of Overexposure:HTLH HAZ:INHALING CONTENTS CAN BE
HARMFUL/FATAL. CHRONIC:AVOID LONG TERM/RPTD CONT. SIGN/SYMPS:EYE
WATERING, HDCH, NAUS, DIZZ & LOSS OF COORD ARE INDICATIONS THAT
SOLV LEVELS ARE TOO HIGH. REDNESS, IT CHING, BURNING SENSATION &
VISUAL DISTURB MAY INDICATE EXCESSIVE EYE CONT. DRYNESS, ITCHING,
CRACKING, (SUPP DATA)
Medical Cond Aggravated by Exposure:NOT APPLICABLE.

First Aid:INGEST:IF SWALLOWED, DO NOT INDUCE VOM. EYE:FLUSH IMMED
W/PLENTY OF WATER FOR AT LEAST 15 MINS. SKIN:FLUSH IMMED W/PLENTY
OF WATER FOLLOWED BY WASHING W/SOAP & WATER. INHAL:IF AFFECTED BY
INHAL OF VAP /SPRAY MIST, REMOVE TO FRESH AIR. APPLYARTF RESP &
OTHER SUPPORTIVE MEASURES AS REQD. OTHER:IN CASE OF ACCIDENTAL
SKIN/EYE CONT, AVOID CONCURRENT EXPOS TO SUN/OTHER SOURCES OF UV
LIGHT. (ING 4)

Flash Point Method:PMCC
Flash Point:88.0F,31.1C
Lower Limits:1.1
Extinguishing Media:NFPA CLASS B EXTING (CO*2, DRY CHEM OR UNIVERSAL AQ
FILM FORMING FOAM) DESIGNED TO EXTING NFPA CLASS IC FLAM LIQ FIRES.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPRVD SCBA & FULL PROT EQUIP
. WATER SPRAY MAY BE INEFT, BUT MAY BE USED TO COOL CLSD CONTRS TO
PVNT PRESS BUILD-UP & POSS (SUPP DATA)
Unusual Fire/Explosion Hazard:KEEP CONTRS TIGHTLY CLSD. ISOLATE FROM
HEAT, ELEC EQUIP, SPARKS & OPEN FLAMES. CLSD CONTRS MAY EXPLODE
WHEN EXPOSED TO EXTREME HEAT. DO NOT APPLY ON (SUPP DATA)

Spill Release Procedures:PROVIDE MAX VENT. ONLY PERS EQUIPPED W/PROPER
NIOSH/MSHA APPRVD RESP & SKIN/EYE PROT SHOULD BE PERMITTED IN AREA.
REMOVE ALL SOURCES OF IGNIT. TAKE UP SPILLED MATL W/SAWDUST,
VERMICULITE OR OTHER ABSO RB MATL & PLACE INTO CONTAINERS FOR
DISPOSAL.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:DO NOT STORE ABOVE 90F. STORE LGE QTYS
IN BLDGS DESIGNED & PROTECTED FOR STOR OF NFPA CLASS IC FLAMM
LIQUIDS. CONTRS SHOULD BE GROUNDED WHEN POURING.
Other Precautions:AVOID FREE FALL OF LIQ IN EXCESS OF A FEW INCHES. IF
THIS MATL IS PART OF A MULTIPLE COMPONENT COATING SYSTEM, READ THE
MSDS FOR OTHER COMPONENT/COMPONENTS BEFORE BLENDING AS RESULTING
MIX MAY HAVE TH E HAZARDS OF ALL OF ITS PARTS.

Respiratory Protection:OVEREXPOS TO VAPS MAY BE PVNTD BY ENSURING VENT,
CONTROLS, VAP EXHST OR FRESH AIR ENTRY. NIOSH/MSHA APPRVD (TC-23C)
ORG VAP RESPS MAY ALSO REDUCE EXPOS. READ RESP MFRS INSTRUCTIONS &
LITERATURE CAREFU LLY TO DETERM TYPE OF (ING 7)
Ventilation:PROVIDE GEN DILUTION OR LOC EXHST VENT IN VOL & PATERN TO
KEEP CONC OF INGREDS LISTED IN INGRED SECT BELOW (ING 8)
Protective Gloves:POLYETHYLENE, BUTYL/NITRILE RUB GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:WEAR PROTECTIVE CLOTHING, INCLUDING
IMPERMEABLE APRON CONSTRUCTED OF POLYETHYLENE, BUTYL RUBBER OR
NITRILE RUBBER.
Work Hygienic Practices:CLEAN OR DISCARD CONTAMINATED CLOTHING & SHOES.
Supplemental Safety and Health
FIRE FIGHT PROC:AUTOIGNIT/EXPLOS WHEN EXPOSED TO EXTREME HEAT. IF WATER
IS USED, FOG NOZZ ARE PREFERABLE. EXPLO HAZ:HOT SURF. TOX GASES MAY
FORM WHEN PROD IS CONTACTED BY FLAME/HOT SURF. HAZ DECOMP PR
OD:PRDCE FUMES INCL:CARBON MONOXIDE. EFTS OF OVEREXP:BURNING,
REDNESS & SWELLING CNDTNS ASSOC W/EXCESSIVE SKIN CONT.

HCC:F4
Boiling Pt:B.P. Text:>295F,>146C
Vapor Pres:0.5
Vapor Density:HVR/AIR
Spec Gravity:1.42
Evaporation Rate & Reference:49 (BUTYL ACETATE=1)
Solubility in Water:O.O%
Appearance and Odor:VISCOUS LIQ W/A DISTINCTIVE ODOR THAT IS
CHARACTERISTIC OF UV/EB CURABLE MATLS.
Percent Volatiles by Volume:23.40

Stability Indicator/Materials to Avoid:NO
FREE RADICAL INITIATORS, PEROXIDES, STRONG ALKALIES OR REACTIVE METALS
COULD CAUSE MATLS TO POLYMERIZE EXOTHERMICALLY.
Stability Condition to Avoid:EXPOSURE TO HIGH TEMPS (>90F) & STRONG UV
LIGHT SOURCES. SEE ALSO MATERIALS TO AVOID.
Hazardous Decomposition Products:MAY PRDCE HAZ DECOMP PRODS WHEN
HEATED, WELDING, BRAZING OR FLAME CUTTING ON SURF COATED W/THIS
PROD MAY (SUPP DATA)
Conditions to Avoid Polymerization:EXPOSURE TO HIGH TEMPERATURE (>90F)
& STRONG UV LIGHT SOURCES. ALSO SEE MATERIALS TO AVOID.

Waste Disposal Methods:WASTE MATERIAL MUST BE DISPOSED OF IN ACCORDANCE
W/FEDERAL, STATE, PROVINCIAL & LOCAL ENVIRONMENTAL CONTROL
REGULATIONS. EMPTY CONTAINERS SHOULD BE RECYCLED OR DISPOSED OF
THOROUGH AN APPROVED WASTE M ANAGEMENT FACILITY.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.